Datasheet 搜索 > EEPROM芯片 > Microchip（微芯） > 25C040-I/P 数据手册 > 25C040-I/P 数据手册 6/22 页
器件3D模型￥ 4.01
25C040-I/P 数据手册 - Microchip（微芯）
制造商:
Microchip（微芯）
分类:
EEPROM芯片
封装:
DIP-8
描述:
25C040 系列 4 Kb (512 x 8) 5.5 V 通孔 SPI 总线 串行 EEPROM - DIP-8
Pictures:
3D模型
符号图
焊盘图
引脚图
产品图
页面导航:
引脚图在P6Hot
标记信息在P12
封装信息在P12P13P14P15P19
功能描述在P7
导航目录
25C040-I/P数据手册
Page:
of 22 Go
若手册格式错乱，请下载阅览PDF原文件
25AA040/25LC040/25C040
DS21204E-page 6 © 2006 Microchip Technology Inc.
2.0 PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 2-1.
TABLE 2-1: PIN FUNCTION TABLE
2.1 Chip Select (CS)
A low level on this pin selects the device. A high level
deselects the device and forces it into Standby mode.
However, a programming cycle which is already
initiated or in progress will be completed, regardless of
the CS
input signal. If CS is brought high during a
program cycle, the device will go in Standby mode as
soon as the programming cycle is complete. When the
device is deselected, SO goes into the high-impedance
state, allowing multiple parts to share the same SPI
bus. A low-to-high transition on CS
after a valid write
sequence initiates an internal write cycle. After power-
up, a low level on CS is required prior to any sequence
being initiated.
2.2 Serial Output (SO)
The SO pin is used to transfer data out of the 25XX040.
During a read cycle, data is shifted out on this pin after
the falling edge of the serial clock.
2.3 Write-Protect (WP)
This pin is a hardware write-protect input pin. When
WP
is low, all writes to the array or STATUS register
are disabled, but any other operation functions
normally. When WP is high, all functions, including
nonvolatile writes operate normally. WP
going low at
any time will reset the write enable latch and inhibit
programming, except when an internal write has
already begun. If an internal write cycle has already
begun, WP
going low will have no effect on the write.
See Table 3-3 for Write-Protect Functionality Matrix.
2.4 Serial Input (SI)
The SI pin is used to transfer data into the device. It
receives instructions, addresses and data. Data is
latched on the rising edge of the serial clock.
2.5 Serial Clock (SCK)
The SCK is used to synchronize the communication
between a master and the 25XX040. Instructions,
addresses or data present on the SI pin are latched on
the rising edge of the clock input, while data on the SO
pin is updated after the falling edge of the clock input.
2.6 Hold (HOLD)
The HOLD pin is used to suspend transmission to the
25XX040 while in the middle of a serial sequence
without having to retransmit the entire sequence again
at a later time. It must be held high any time this func-
tion is not being used. Once the device is selected and
a serial sequence is underway, the HOLD
pin may be
pulled low to pause further serial communication
without resetting the serial sequence. The HOLD pin
must be brought low while SCK is low, otherwise the
HOLD function will not be invoked until the next SCK
high-to-low transition. The 25XX040 must remain
selected during this sequence. The SI, SCK and SO
pins are in a high-impedance state during the time the
part is paused and transitions on these pins will be
ignored. To resume serial communication, HOLD
must
be brought high while the SCK pin is low, otherwise
serial communication will not resume. Lowering the
HOLD line at any time will tri-state the SO line.
Name PDIP SOIC TSSOP Description
CS
1 1 3 Chip Select Input
SO 2 2 4 Serial Data Output
WP
3 3 5 Write-Protect Pin
V
SS 4 4 6 Ground
SI 5 5 7 Serial Data Input
SCK 6 6 8 Serial Clock Input
HOLD
7 7 1 Hold Input
V
CC 8 8 2 Supply Voltage
器件 Datasheet 文档搜索
AiEMA 数据库涵盖高达 72,405,303 个元件的数据手册，每天更新 5,000 多个 PDF 文件
