Datasheet 搜索 > 实时时钟芯片 > Maxim Integrated（美信） > DS1307Z 数据手册 > DS1307Z 数据手册 6/14 页
器件3D模型￥ 14.6
DS1307Z 数据手册 - Maxim Integrated（美信）
制造商:
Maxim Integrated（美信）
分类:
实时时钟芯片
封装:
SOIC-8
描述:
64 ×8 ，串行， I²C实时时钟 64 x 8, Serial, I2C Real-Time Clock
Pictures:
3D模型
符号图
焊盘图
引脚图
产品图
页面导航:
导航目录
DS1307Z数据手册
Page:
of 14 Go
若手册格式错乱，请下载阅览PDF原文件
DS1307 64 x 8, Serial, I
2
C Real-Time Clock
PIN DESCRIPTION
PIN NAME FUNCTION
1 X1
Connections for Standard 32.768kHz Quartz Crystal. The internal oscillator circuitry is
designed for operation with a crystal having a specified load capacitance (C
L
) of 12.5pF.
X1 is the input to the oscillator and can optionally be connected to an external 32.768kHz
oscillator. The output of the internal oscillator, X2, is floated if an external oscillator is
connected to X1.
Note: For more information on crystal selection and crystal layout considerations, refer to
Application Note 58: Crystal Considerations with Dallas Real-Time Clocks.
2 X2
3 V
BAT
Backup Supply Input for Any Standard 3V Lithium Cell or Other Energy Source. Battery
voltage must be held between the minimum and maximum limits for proper operation.
Diodes in series between the battery and the V
BAT
pin may prevent proper operation. If a
backup supply is not required, V
BAT
must be grounded. The nominal power-fail trip point
(V
PF
) voltage at which access to the RTC and user RAM is denied is set by the internal
circuitry as 1.25 x V
BAT
nominal. A lithium battery with 48mAh or greater will back up the
DS1307 for more than 10 years in the absence of power at +25°C.
UL recognized to ensure against reverse charging current when used with a lithium
battery. Go to: www.maxim-ic.com/qa/info/ul/
.
4 GND Ground
5 SDA
Serial Data Input/Output. SDA is the data input/output for the I
2
C serial interface. The
SDA pin is open drain and requires an external pullup resistor. The pullup voltage can be
up to 5.5V regardless of the voltage on V
CC
.
6 SCL
Serial Clock Input. SCL is the clock input for the I
2
C interface and is used to synchronize
data movement on the serial interface. The pullup voltage can be up to 5.5V regardless of
the voltage on V
CC
.
7 SQW/OUT
Square Wave/Output Driver. When enabled, the SQWE bit set to 1, the SQW/OUT pin
outputs one of four square-wave frequencies (1Hz, 4kHz, 8kHz, 32kHz). The SQW/OUT
pin is open drain and requires an external pullup resistor. SQW/OUT operates with either
V
CC
or V
BAT
applied. The pullup voltage can be up to 5.5V regardless of the voltage on
V
CC
. If not used, this pin can be left floating.
8 V
CC
Primary Power Supply. When voltage is applied within normal limits, the device is fully
accessible and data can be written and read. When a backup supply is connected to the
device and V
CC
is below V
TP
, read and writes are inhibited. However, the timekeeping
function continues unaffected by the lower input voltage.
DETAILED DESCRIPTION
The DS1307 is a low-power clock/calendar with 56 bytes of battery-backed SRAM. The clock/calendar provides
seconds, minutes, hours, day, date, month, and year information. The date at the end of the month is automatically
adjusted for months with fewer than 31 days, including corrections for leap year. The DS1307 operates as a slave
device on the I
2
C bus. Access is obtained by implementing a START condition and providing a device identification
code followed by a register address. Subsequent registers can be accessed sequentially until a STOP condition is
executed. When V
CC
falls below 1.25 x V
BAT
, the device terminates an access in progress and resets the device
address counter. Inputs to the device will not be recognized at this time to prevent erroneous data from being
written to the device from an out-of-tolerance system. When V
CC
falls below V
BAT
, the device switches into a low-
current battery-backup mode. Upon power-up, the device switches from battery to V
CC
when V
CC
is greater than
V
BAT
+0.2V and recognizes inputs when V
CC
is greater than 1.25 x V
BAT
. The block diagram in Figure 1 shows the
main elements of the serial RTC.
6 of 14
器件 Datasheet 文档搜索
AiEMA 数据库涵盖高达 72,405,303 个元件的数据手册，每天更新 5,000 多个 PDF 文件
