Web Analytics
Datasheet 搜索 > ADI(亚德诺) > LTC490CS8#PBF 数据手册 > LTC490CS8#PBF 数据手册 6/12 页
LTC490CS8#PBF
器件3D模型
40.35
导航目录
  • 典型应用电路图在P6
  • 焊盘布局在P11
  • 技术参数、封装参数在P3
  • 应用领域在P1
LTC490CS8#PBF数据手册
Page:
of 12 Go
若手册格式错乱,请下载阅览PDF原文件
LTC490
6
490fb
Typical Application
A typical connection of the LTC490 is shown in Figure 5.
Two twisted-pair wires connect two driver/receiver pairs
for full duplex data transmission. Note that the driver and
receiver outputs are always enabled. If the outputs must
be disabled, use the LTC491.
There are no restrictions on where the chips are con-
nected, and it isn’t necessary to have the chips connected
at the ends of the wire. However, the wires must be
terminated only at the ends with a resistor equal to their
characteristic impedance, typically 120. Because only
one driver can be connected on the bus, the cable can be
terminated only at the receiving end. The optional shields
around the twisted pair help reduce unwanted noise, and
are connected to GND at one end.
The LTC490 can also be used as a line repeater as shown
in Figure 6. If the cable length is longer than 4000 feet, the
LTC490 is inserted in the middle of the cable with the
receiver output connected back to the driver input.
Thermal Shutdown
The LTC490 has a thermal shutdown feature which pro-
tects the part from excessive power dissipation. If the
outputs of the driver are accidently shorted to a power
supply or low impedance, source, up to 250mA can flow
through the part. The thermal shutdown circuit disables
the driver outputs when the internal temperature reaches
150°C and turns them back on when the temperature
cools to 130°C. If the outputs of two or more LTC490
drivers are shorted directly, the driver outputs can not
supply enough current to activate the thermal shutdown.
Thus, the thermal shutdown circuit will not prevent con-
tention faults when two drivers are active on the bus at the
same time.
Cables and Data Rate
The transmission line of choice for RS485 applications is
a twisted pair. There are coaxial cables (twinaxial) made
for this purpose that contain straight pairs, but these are
Figure 5. Typical Connection
Figure 6. Line Repeater
APPLICATIO S I FOR ATIO
WUUU
LTC490 • F05
120
120
SHIELD
LTC490
DRIVER
RECEIVER
LTC490
DRIVER
DX
RX
DX
RX
2
3
5
6
7
8
RECEIVER
0.01µF
1
4
5V
SHIELD
8
7
6
5
0.01µF
5V
4
2
3
1
+
+
LTC490 • F06
120
LTC490
DRIVERDX
RX
2
3
5
6
7
8
RECEIVER DATA IN
DATA OUT

LTC490CS8#PBF 数据手册

ADI(亚德诺)
12 页 / 0.16 MByte
ADI(亚德诺)
2 页 / 0.18 MByte
ADI(亚德诺)
2 页 / 0.27 MByte

LTC490CS8 数据手册

Linear Technology(凌力尔特)
ADI(亚德诺)
Linear Technology(凌力尔特)
RS-485 线路驱动器和接收器,Linear Technology**Linear Technology** 的 RS485 标准广泛用于本地网络以及长距离数据传输,特别适用于工业和商业应用。 执行 Profibus(过程现场总线)协议,适用于工厂和流程自动化环境中的现场总线解决方案。 RS422 标准类似于 RS485 标准,但不允许一个总结上有多个驱动器。 RS485 收发器(之前为 TIA-485)定义了高达 10Mbps 的差分数据传输速率。低功率 CMOS RS485/RS422 接口收发器具有故障保护接收器、高电压、高数据 传输速率、高 ESD 保护类型和收发器 (TXRX),具有引脚控制可切换 120Ω 端接电阻器。 平衡线路提供出色的噪声抑制能力 ### RS-485 线路驱动器和接收器
ADI(亚德诺)
ADI(亚德诺)
Linear Technology(凌力尔特)
Linear Technology(凌力尔特)
RS-422/RS-485 接口 IC LTC490 - Differential Driver and Receiver Pair
ADI(亚德诺)
器件 Datasheet 文档搜索
器件加载中...
AiEMA 数据库涵盖高达 72,405,303 个元件的数据手册,每天更新 5,000 多个 PDF 文件