Datasheet 搜索 > DC/DC转换器 > TI（德州仪器） > TPS61040DBVR 数据手册 > TPS61040DBVR 数据手册 3/25 页
￥ 0.922
TPS61040DBVR 数据手册 - TI（德州仪器）
制造商:
TI（德州仪器）
分类:
DC/DC转换器
封装:
SOT-23-5
描述:
TEXAS INSTRUMENTS TPS61040DBVR 直流-直流开关升压稳压器, 可调, 1.8V-6V输入, 1.8V-28V输出, 400mA输出, SOT-23-5
Pictures:
3D模型
符号图
焊盘图
引脚图
产品图
页面导航:
导航目录
TPS61040DBVR数据手册
Page:
of 25 Go
若手册格式错乱，请下载阅览PDF原文件
I
peak(typ)
+ I
LIM
)
V
IN
L
100 ns
I
peak(typ)
+ 400 mA )
V
IN
L
100 ns for the TPS61040
I
peak(typ)
+ 250 mA )
V
IN
L
100 ns for the TPS61041
TPS61040
TPS61041
www.ti.com
SLVS413F –OCTOBER 2002–REVISED DECEMBER 2010
Table 2. Terminal Functions
TERMINAL
I/O DESCRIPTION
DDC,
NAME DRV NO.
DBV NO.
This is the enable pin of the device. Pulling this pin to ground forces the device into shutdown
EN 4 3 I mode reducing the supply current to less than 1 mA. This pin should not be left floating and needs
to be terminated.
This is the feedback pin of the device. Connect this pin to the external voltage divider to program
FB 3 4 I
the desired output voltage.
GND 2 1 – Ground
NC – 5 – No connection
Connect the inductor and the Schottky diode to this pin. This is the switch pin and is connected to
SW 1 6 I
the drain of the internal power MOSFET.
V
IN
5 2 I Supply voltage pin
DETAILED DESCRIPTION
OPERATION
The TPS61040/41 operates with an input voltage range of 1.8 V to 6 V and can generate output voltages up to
28 V. The device operates in a pulse-frequency-modulation (PFM) scheme with constant peak current control.
This control scheme maintains high efficiency over the entire load current range, and with a switching frequency
up to 1 MHz, the device enables the use of very small external components.
The converter monitors the output voltage, and as soon as the feedback voltage falls below the reference voltage
of typically 1.233 V, the internal switch turns on and the current ramps up. The switch turns off as soon as the
inductor current reaches the internally set peak current of typically 400 mA (TPS61040) or 250 mA (TPS61041).
See the Peak Current Control section for more information. The second criteria that turns off the switch is the
maximum on-time of 6 ms (typical). This is just to limit the maximum on-time of the converter to cover for extreme
conditions. As the switch is turned off the external Schottky diode is forward biased delivering the current to the
output. The switch remains off for a minimum of 400 ns (typical), or until the feedback voltage drops below the
reference voltage again. Using this PFM peak current control scheme the converter operates in discontinuous
conduction mode (DCM) where the switching frequency depends on the output current, which results in very high
efficiency over the entire load current range. This regulation scheme is inherently stable, allowing a wider
selection range for the inductor and output capacitor.
PEAK CURRENT CONTROL
The internal switch turns on until the inductor current reaches the typical dc current limit (I
LIM
) of 400 mA
(TPS61040) or 250 mA (TPS61041). Due to the internal propagation delay of typical 100 ns, the actual current
exceeds the dc current limit threshold by a small amount. The typical peak current limit can be calculated:
(1)
The higher the input voltage and the lower the inductor value, the greater the peak.
By selecting the TPS61040 or TPS61041, it is possible to tailor the design to the specific application current limit
requirements. A lower current limit supports applications requiring lower output power and allows the use of an
inductor with a lower current rating and a smaller form factor. A lower current limit usually has a lower output
voltage ripple as well.
Copyright © 2002–2010, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Link(s): TPS61040 TPS61041
Downloaded from Elcodis.com electronic components distributor
器件 Datasheet 文档搜索
AiEMA 数据库涵盖高达 72,405,303 个元件的数据手册，每天更新 5,000 多个 PDF 文件
