Datasheet 搜索 > DA转换器 > ADI（亚德诺） > AD5383BSTZ-5 数据手册 > AD5383BSTZ-5 用户编程技术手册 1/2 页
器件3D模型￥ 67.46
AD5383BSTZ-5 用户编程技术手册 - ADI（亚德诺）
制造商:
ADI（亚德诺）
分类:
DA转换器
封装:
LQFP-100
描述:
ANALOG DEVICES AD5383BSTZ-5 数模转换器, 12 bit, 167 kSPS, 并行、串行, 4.5V 至 5.5V, LQFP, 100 引脚
Pictures:
3D模型
符号图
焊盘图
引脚图
产品图
页面导航:
原理图在P1
导航目录
AD5383BSTZ-5数据手册
Page:
of 2 Go
若手册格式错乱，请下载阅览PDF原文件
AN-1228
APPLICATION NOTE
One Technology Way • P. O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
32 Channels of Programmable Voltage with Excellent Temperature Drift
Performance Using the AD5383 DAC
Rev. B | Page 1 of 2
CIRCUIT FUNCTION AND BENEFITS
This circuit is a multichannel digital-to-analog converter (DAC)
configuration with excellent temperature drift performance. It
provides 32 individual voltage channels with 12 bits of resolution
and a temperature stability of typically less than 3 ppm/°C.
CIRCUIT DESCRIPTION
Table 1. Devices Connected/Referenced
Product Description
AD5383 32-channel 12-bit 3 V/5 V single-supply DAC
ADR421 Low noise, 2.500 V XFET® voltage reference
ADR431 Ultralow noise XFET voltage reference
Figure 1 shows a typical configuration for the AD5383 when
configured for use with an external reference. In the circuit
shown, all AGND, SIGNAL_GND, and DAC_GND pins are
tied together to a common AGND. AGND and DGND are
connected together at the
AD5383 device. On power-up, the
AD5383 defaults to external reference operation.
This design uses two separate 5.0 V power supplies: one to power
the voltage reference and the analog portion of the
AD5383
(AVDD), and the other to power the digital portion of the
AD5383 (DVDD). For best performance, always use a linear
regulator to power the analog portion of the circuit. If a switching
regulator is used to power the digital portion, take care to minimize
switching noise at the DVDD supply pins. Additional decoupling
using a series connected ferrite bead may be required. The
AD5383
digital (DVDD) power supply can operate from a 3 V or 5 V
supply, which provides for maximum flexibility when interfacing
to digital components. Both supplies can be tied together to a
common 5 V supply, provided that supply is derived from a linear
regulator. Refer to the ADIsimPower design tool for guidance
on the power supply designs.
It is recommended to decouple close to the device with a 0.1 µF
ceramic and a 10 µF tantalum capacitor. In this circuit, the
reference for the
AD5383 is provided externally from either an
ADR421 or ADR431 2.5 V reference. The ADR431 provides a
lower output voltage noise specification for applications where
that specification is important. Decouple the reference at the
REFOUT/REFIN pin of the device with a 0.1 µF capacitor.
COMMON VARIATIONS
A variation of this circuit is the AD5383-3 with the ADR280 1.2 V
reference where all other connections and components are the
same as those previously outlined.
08205-001
ADR431/
ADR421
AD5383-5
AV
DD
DV
DD
SIGNAL_GNDDAC_GND DGND
V
OUT
31
V
OUT
0
AGND
REFOUT/REFIN
REFGND
2.5V
5.0V 5.0V
0.1µF
10µF 0.1µF
0.1µF
Figure 1. AD5383 Typical Configuration with External Reference (Simplified Schematic)
器件 Datasheet 文档搜索
AiEMA 数据库涵盖高达 72,405,303 个元件的数据手册，每天更新 5,000 多个 PDF 文件
