Datasheet 搜索 > 陶瓷电容 > muRata（村田） > GRT31CR61H106KE01L 数据手册 > GRT31CR61H106KE01L 数据手册 4/28 页
器件3D模型￥ 0.334
GRT31CR61H106KE01L 数据手册 - muRata（村田）
制造商:
muRata（村田）
分类:
陶瓷电容
封装:
1206
描述:
MURATA GRT31CR61H106KE01L 多层陶瓷电容器, 表面贴装, 1206 [3216 公制], 10 µF, 50 V, ± 10%, X5R, GRT Series 新
Pictures:
3D模型
符号图
焊盘图
引脚图
产品图
页面导航:
导航目录
GRT31CR61H106KE01L数据手册
Page:
of 28 Go
若手册格式错乱，请下载阅览PDF原文件
13 Thermal Shock The measured and observed characteristics shall satisfy the
Fix the capacitor to the supporting jig in the same manner and under
specifications in the following table.
the same conditions as (18). Perform the 300 cycles according to
Appearance
No marking defects
the two heat treatments listed in the following table (Maximum
Capacitance
R6,C8: Within ±10.0%
transfer time is 20 seconds).
Change
Set for 24±2 hours at room temperature, then measure.
Dissipation
R6,C8: 0.125max
Factor
Insulation
50Ω ・F min.
Resistance
・Initial measurement for high dielectric constant type
Perform a heat treatment at 150+0/-10 for one hour and then set
for 24±2 hours at room temperature.
Perform the initial measurement.
14 ESD
Appearance
No marking defects
Per AEC-Q200-002
Capacitance
Within the specified tolerance
Voltage setting level : 2kV
Change
Dissipation
R6,C8: 0.125max
Factor
Insulation
50Ω ・F min.
Resistance
15 Solderability
(a) Preheat at 155℃ for 4 hours. After preheating, immerse the
capacitor in a solution of ethanol(JIS-K-8101) and rosin (JIS-K-
5902) (25% rosin in weight proportion). Immerse in
eutectic solder solution for 5+0/-0.5 seconds at 235±5℃.
(b) Should be placed into steam aging for 8 hours±15 minutes.
After preheating, immerse the capacitor in a solution of
ethanol(JIS-K-8101) and rosin (JIS-K-5902) (25% rosin in weight
proportion). Immerse in eutectic solder solution for 5+0/-0.5
seconds at 235±5℃.
(c) Should be placed into steam aging for 8 hours±15 minutes.
After preheating, immerse the capacitor in a solution of
ethanol(JIS-K-8101) and rosin (JIS-K-5902) (25% rosin in weight
proportion). Immerse in eutectic solder solution for 120±5 seconds
at 260±5℃.
16 Electrical
Appearance
No defects or abnormalities Visual inspection.
Chatacteri-
Capacitance
Within the specified tolerance
The capacitance/Q/D.F. should be measured at 25℃ at the
zation
Change
frequency and voltage shown in the table.
Dissipation
R6.C8 :0.125max
Factor
Insulation
50Ω ・F min.
The insulation resistance should be measured with a DC voltage not
Resistance
exceeding the rated voltage at 25℃ and maximum operating temperature
※
25℃
within 1 minute of charging.
Insulation
5Ω ・F min.
Resistance
※85+3/-0℃(For R6), 105+3/-0℃(For C8)
85℃(For R6)
105℃(For C8)
Dielectric
No failure No failure should be observed when 250% of the rated voltage is
Strength
applied between the terminations for 1 to 5 seconds, provided the
charge/ discharge current is less than 50mA.
95% of the terminations is to be soldered evenly and continuously.
■AEC-Q200 Murata Standard Specification and Test Methods
No
AEC-Q200 Test Item
AEC-Q200 Test Method
Specifications.
Step
1
2
Temp.
(℃)
-55+0/-3
105+3/-0 (For C8)
85+3/-0 (For R6)
Time
(min.)
15±3
15±3
Char.
Item
R6,C8
6.3V max.
(C≦10F)
R6,C8
10V min.
(C≦10F)
R6,C8
(10F< C)
Frequency
10.1kHz
10.1kHz
12024Hz
Voltage
0.50.1Vrms
10.2Vrms
0.50.1Vrms
JEMCGS-01744J 4
器件 Datasheet 文档搜索
AiEMA 数据库涵盖高达 72,405,303 个元件的数据手册，每天更新 5,000 多个 PDF 文件
